Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTherma-Tru Door Installation in Vero Beach: What to Know First
TruePane Windows & Doors installs, replaces, and adjusts Therma-Tru entry doors, French doors, and storm doors throughout Vero Beach. As an independent Therma-Tru service provider, we handle the full job from opening inspection to final hardware adjustment, typically completing most single-door replacements in one visit. Exact cost depends on the door line, the condition of the rough opening, and whether we’re pulling the old frame or setting a pre-hung unit, but you’ll get a written line-item quote before any work begins.
This page is written for the homeowner who already owns a Therma-Tru door, or the one who is considering one and wants to know how it holds up in Vero Beach salt air and hurricane season. If you need a door set right, and you want it dependable for the next twenty years, call (772) 279-7983 and we’ll walk you through it.
How Therma-Tru Products Fail - and How We Fix Them
Therma-Tru builds a solid door. We have installed enough of them to know that most failures in Vero Beach are not the slab itself but the installation method, the frame, or the seal system. Here is what we see most often, on which lines, and what we do about it.
- Fiber-Classic and Smooth-Star slab separation at the stile edges. The compression-molded skin can pull away from the frame edge after years of direct sun on west-facing entries along Route 60 and the Miracle Mile corridor. It happens because the adhesive bond breaks down faster in sustained heat. Our fix is a full re-bond with a marine-grade adhesive, or a replacement slab if the separation runs more than a few inches. Cheap caulk jobs do not hold; we do not do cheap caulk jobs.
- Benchmark by Therma-Tru steel doors rusting along the bottom sweep and corners. These doors are built to a price point, not a climate. In Vero Beach, the salt air gets into the bottom corners where factory paint is thinnest. We remove the rust mechanically, prime with a corrosion inhibitor, and refinish before reinstalling the sweep. If the rust has gone through the steel, replacement is the honest call.
- Classic-Craft and Estate Series wood-grain skins bubbling or peeling on the lock stile. These are premium doors, but they are still molded skins over a core. When the factory finish is compromised by a poor seal at the weatherstrip, moisture wicks in and lifts the grain layer. We sand, re-seal, and match the factory finish, then set the door so the weatherstrip actually compresses evenly. Half the time the door was hung out of square and nobody ever checked it.
- Faulty factory weatherstrip seal on pre-hung units, particularly on the Benchmark line. The magnetic seal is good when it seats, but if the jamb is out of plane by even an eighth of an inch, you get light gaps and water intrusion along the hinge side during a heavy afternoon storm. We pull the brickmold, shim the jamb correctly, and re-secure so the seal seats all the way around. This is the most common cause of “mystery” air leaks in Vero Beach entryways.
- Fiberglass frame rot confusion on aging installations. Homeowners often think a Therma-Tru door has “rotten wood” when what is actually happening is a failed sill pan underneath. Water pools at the threshold, wicks into the subfloor, and the frame begins to move. A new door set into a failed pan will do the same thing. We pull the door, inspect the pan, replace or repair it, and reset the door on a proper slope-to-drain pan. Dale Kessler has pulled enough of these apart to tell you: the door was not the problem; the pan was.
Our Therma-Tru Door Installation Process
- 1
You call, a person answers. Our live line, not a voicemail tree, takes your call 24/7 and schedules your estimate.
- 2
We measure the opening twice. Every technician checks the rough opening height, width, and diagonal on both sides. A Therma-Tru pre-hung unit depends on square framing more than most, so this step is not optional.
- 3
We quote side by side on paper. You see the OEM part, the aftermarket alternative, and the honest trade-off in writing. We do not hide behind vague estimates.
- 4
We set the frame, not just the door. Jamb shims, sill pan, brickmold, and hardware all get set in that order. The slab hangs last, once the frame is actually planted and plumb.
- 5
We test seals, swing, and sweep before cleanup. The door must close with a consistent gap on all sides. If it binds in July, it binds today, and we fix it before we leave.
- 6
Both warranty layers are registered in writing. That is The Keystone Standard, and it happens before the truck pulls out. Then you get the Done Right Promise in writing.
What Therma-Tru Door Installation Costs in Vero Beach
- Slab replacement only (same frame, no structural work): $850-$1,600 depending on series and size.
- Full pre-hung door replacement, single entry: $1,800-$4,200 for Benchmark and Fiber-Classic lines; $4,500-$8,000 for Classic-Craft and Estate Series with glass and upgraded hardware.
- French door or double door replacement: $3,500-$9,000 depending on configuration and glass package.
- Storm door installation over existing entry: $400-$1,100 including hardware and weatherproofing.
- Threshold and sill pan repair or replacement: $350-$900, depending on how much subfloor has been compromised.
What moves the price in Vero Beach is usually the opening, not the door. Older block homes in the Miracle Mile corridor often have out-of-square framing, water damage at the sill, or failed pans that need true carpentry before a new door can sit right. We quote that honestly before we start, so you never get a surprise line item on the bill. Call (772) 279-7983 and we’ll give you a real number for your door and your opening.
Why Vero Beach Homeowners Call TruePane Windows & Doors for Therma-Tru Work
We have been serving this community since 2008, with Dale Kessler running the shop since 2008 on a simple rule his father taught him: if the pane is not true, the job is not done. That applies to every Therma-Tru door we set, from a Benchmark front entry on a barrier island condo to a Classic-Craft double door in Hawks Nest. The Done Right Promise means if something is not right after we leave, we come back and make it right. No paperwork fights, no arguing. And because we are also an authorized installer for PGT, CGI, CWS, and ES Windows, we can show you alternatives side by side if a Therma-Tru is not the right fit for a particular opening or a hurricane exposure. A live person answers every call, 24/7. We’ll be there when we say.
If it is not right on the day we leave, it is not right.
FAQs
No. Therma-Tru warranties cover the door itself; the installation workmanship is covered by whoever sets it. What matters is that the installation follows the manufacturer’s written installation instructions, because a botched install can void the door warranty. We install as an independent Therma-Tru service provider and document every step so you have a record if you ever need to file a claim. If a warranty question comes up, call (772) 279-7983 and we’ll help you sort it out.
Most repairs are possible. Slab re-bonding, weatherstrip replacement, threshold work, hinge adjustment, hardware replacement, and glass insert replacement are all routine for us. We replace when the core is compromised, the frame is failing, or the cost of repair outpaces the value of the existing door. We’ll tell you plainly which is the right call and quote both options in writing.
A straightforward slab replacement or pre-hung single door job usually takes one day from setup to final cleanup. Double doors or jobs with sill pan replacement or framing repair can run a second day. We give you a schedule before we start and we keep it.
Yes. We install Therma-Tru’s impact-rated fiberglass door configurations, and we also show side-by-side quotes for PGT, CGI, CWS, and ES Windows impact doors where the opening or exposure calls for it. Hurricane-rated doors in Vero Beach need to meet both Miami-Dade and Florida Building Code requirements, and we pull permits and pass inspections on every job. Ask us about your specific exposure and insurance requirements. Call (772) 279-7983 for a free estimate with no obligation.
Both. We stock common OEM parts like Therma-Tru climate seals, sweeps, hinges, and glass frames, and we use them when the door’s age and warranty status call for factory components. For older doors or parts with long lead times, we can recommend quality aftermarket equivalents that meet the same fit and finish. You get the choice in writing, with honest guidance from a technician who has worked on hundreds of these doors in Vero Beach.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Vero Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.