Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterTherma-Tru Roof Replacement & Installation in Vero Beach: What to Know First
Therma-Tru roof replacement and installation in Vero Beach typically runs from $900 to $3,400 depending on the door configuration, whether the frame is salvageable, and how much salt-driven corrosion has set in. Most Therma-Tru entry systems can be measured, ordered, and installed within two to three weeks once we confirm the rough opening. We charge by the job, not the hour, and every quote is a fixed number before we touch a screw.
If you own a Therma-Tru door system and the roof line above it is being replaced, or the frame has shifted and the door no longer closes square, this page tells you what to expect. Call (772) 279-7983 and a live person answers, any hour, any day. We’re an independent Therma-Tru service provider, not a factory affiliate, which means we tell you straight when OEM is worth the wait and when a quality aftermarket part will hold better in our climate.
How Therma-Tru Products Fail - and How We Fix Them
Dale Kessler has seen the same handful of Therma-Tru problems repeat for years, most of them made worse by Vero Beach’s salt air and summer humidity. Here’s what actually fails:
- Fiber-Classic door slab warping on south-facing exposures. The compression-molded fiberglass on older Fiber-Classic models can bow when a roof line changes and channels more direct sun onto one side of the door. We see this on Miracle Mile block homes where a porch was enclosed years ago. The fix is usually a full slab replacement with proper sealing, not a band-aid sanding job.
- Frame rot at the threshold where roof runoff pools. Therma-Tru’s door frames were never designed to sit in standing water. When a roof replacement changes the drip edge or gutter line, water that used to fall away now runs toward the entry. We pull the threshold, check the subfloor, and rebuild the rough opening with rot-resistant material before resetting the unit.
- Weatherstrip channel separation on Smooth-Star models. The adhesive-backed weatherstrip channels on older Smooth-Star systems loosen in high humidity, especially when the gap between the slab and frame was never tuned. The door starts to feel loose and you hear honest air movement at the latch side. We reset the channels with mechanical fasteners and re-tune the slab so the seal actually seats.
- Hinge-side frame compression from roof load transfer. When a section of roof ridge is replaced and the load path shifts, the rough opening can compress just enough to bind the door at the top hinge corner. This is a structural issue, not a door hardware issue, and we identify it by checking the reveal down both sides before touching the hinges.
- Latch-side strike plate drift after re-roofing vibration. Reroofing puts a week of hammering and foot traffic through the framing. On block homes the vibration is absorbed, but on wood-frame construction the strike plate can drift a sixteenth of an inch, and suddenly the deadbolt won’t throw. It’s a fifteen-minute fix if you know where to look, and we do.
Our Therma-Tru Roof Replacement & Installation Process
- 1
Call comes in. A live person answers. You describe the door, the roof work, and what it’s doing. We schedule a slot that actually holds.
- 2
We measure the opening twice. Left jamb, right jamb, head, threshold, and diagonal corners. If the house has moved, we find out before quoting, not after the door is ordered.
- 3
We quote on paper. You see the exact Therma-Tru model, the slab or frame components, the labor, and the warranty terms written out. No allowances, no “we’ll see once we open it up.”
- 4
Parts decision, made together. We lay out OEM versus quality aftermarket side by side, with prices and lead times. If the OEM part is backordered, you know because we tell you, not because you call us three weeks later.
- 5
Install and test. We set the unit, adjust the reveals, throw the deadbolt, swing the door, and run a seal check. If the pane is not true, the job is not done, and we don’t leave until it is.
- 6
Warranty paperwork registered in writing. Both manufacturer warranty layers get registered before our truck leaves the driveway. The Done Right Promise covers the workmanship, in writing, no arguing.
What Therma-Tru Roof Replacement & Installation Costs in Vero Beach
Here are the numbers we quote most often for Therma-Tru work in this area:
| Scope of Work | Typical Range |
|---|---|
| Door slab replacement only (Fiber-Classic or Smooth-Star) | $900 - $1,600 |
| Full frame and slab replacement, standard entry | $1,800 - $2,800 |
| Full system replacement with sidelites | $2,600 - $3,400 |
| Threshold rebuild and subfloor repair | $350 - $700 (added to above) |
| Weatherstrip channel restoration | $150 - $350 |
What moves the price is the condition of the rough opening, whether the frame can be salvaged, and which Therma-Tru series you’re replacing. Homes closer to the barrier island tend to have more corrosion at the threshold, and we factor that in honestly. Call (772) 279-7983 for an exact quote. Estimates are free and the number we give you is the number you pay.
Why Vero Beach Homeowners Call TruePane Windows & Doors for Therma-Tru Work
We’ve been serving this community since 2008 through a heritage that started with Dale Kessler’s finish-carpenter father and continues with the glazing fundamentals Dale learned at Indian River State College before spending two decades setting and troubleshooting doors from Miracle Mile to the barrier island. We’re not a franchise playbook. When a Therma-Tru door fails because the roof line changed and the salt air finished the job, we understand exactly what happened, because we’ve seen it a hundred times.
Every technician who walks through your door is background-checked and uniformed. Every job carries a Done Right Promise and The Keystone Standard: warranty layers registered in writing, durations stated. And if your Therma-Tru system is beyond saving, we also service PGT, CGI, CWS, and ES Windows, so you can compare a full replacement side by side without chasing three different contractors. Call (772) 279-7983. A live person answers, and if it is not right on the day we leave, it is not right.
FAQs
Yes. We photograph and measure the existing slab and frame before any roof work touches the opening, so we can re-set the exact geometry after the framing contractor finishes. If the roof work shifts the rough opening, we catch it before the door goes back in. Call (772) 279-7983 to schedule the pre-roof inspection.
Most Therma-Tru slab replacements are done in a single visit, usually four to six hours. Full frame and slab replacements can run a day to a day and a half depending on the rough opening condition and whether threshold repairs are needed. We give you a written schedule before we start, and we keep it.
Therma-Tru’s product warranty follows the product, not the installer, as long as the unit is installed according to their published guidelines and the warranty is registered properly. We register both manufacturer warranty layers in writing before we leave. Our workmanship is covered separately by the Done Right Promise.
It depends on the frame. If the jambs are square and the threshold is solid, a slab replacement is often the smarter money, usually $900 to $1,600. If the frame is compromised, patching it just delays the same problem by a season, and we’ll tell you so plainly. Call (772) 279-7983 and we’ll give you an honest read over the phone before we ever set an appointment.
When a permit is required for structural work around the rough opening, we handle the permit and the inspection. For straight slab swaps on an existing frame, a permit is typically not required, but we’ll confirm that with the local building department so you’re never surprised. Estimates are free, and the price we quote is the price you pay.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Vero Beach and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.